A single padel court is a structural, electrical, and surfacing project rolled into one purchase decision. The Single Padel Court H004 is positioned as a turnkey system — meaning the steel structure, glass enclosure, playing surface, and lighting are supplied and engineered as one matched package rather than sourced piecemeal. For buyers comparing options, understanding what "turnkey" actually covers, and what site conditions the system requires, matters more than any marketing description.
This guide breaks down the H004's technical specifications, the site planning constraints that determine feasibility, and the procurement steps that reduce installation risk — whether you're a club operator, a hotel developer, a municipal planner, or a contractor preparing a bid.
A turnkey padel court package bundles the structural shell, enclosure, surface, and lighting into a single specified system, engineered to work together rather than assembled from separate vendors after the fact. For the H004, this typically means:
The practical advantage of a turnkey specification is coordination: the steel frame's panel openings are sized to the glass dimensions, the lighting layout matches the court footprint, and the turf is specified for the enclosure's dimensions. Buyers sourcing these components from separate suppliers carry the coordination risk themselves.
Single-court systems like the H004 fit projects where a full multi-court complex isn't the goal — either due to space, budget, or phased rollout plans. This includes:
The H004's frame uses galvanized steel construction, which resists corrosion in both indoor and outdoor installations — an important factor for courts exposed to weather or high humidity. The mesh sections use a 50×50mm grid pattern with wire gauge in the 3.0–4.0mm range.
This mesh specification affects two things buyers should evaluate directly: ball containment (mesh gaps must be tight enough that balls don't pass through during play) and structural rigidity (wire gauge determines how the panel resists impact and wind load over time). When reviewing a quote, confirm the mesh spec matches what's stated here — thinner wire gauge in a cheaper substitute can look identical on a spec sheet but perform differently over years of use.
The glass panels are specified at 12mm tempered glass. Tempered glass is the standard choice for padel enclosures because it's designed to resist impact from gameplay and, if it does fail, breaks into small, less hazardous fragments rather than large shards. The 12mm thickness sits at the upper end of typical padel glass specifications, which generally supports durability under repeated ball contact and player impact at the glass line.
Glass thickness also affects sound transmission and visual clarity for spectators — both relevant if the court will be used for club exhibitions, lessons, or hotel guest viewing.
The playing surface uses 13mm pile height artificial turf with a density of 8000 Dtex and a stitch/tuft density of 52,500 (per the manufacturer's stated specification). These three figures together determine how the ball bounces and how players' feet grip the surface:
Buyers comparing systems should ask suppliers for these three figures specifically — turf described only as "professional grade" without pile height, Dtex, and density figures is not a complete specification.
The H004 lighting package includes 8 fixtures at 200W each, positioned around the court structure for night play. This gives a combined system load of 1,600W, which procurement and electrical teams need for circuit sizing and load calculations — covered further in the site planning section below.
LED fixture count and wattage affect more than brightness; fixture placement (height, angle, and spacing) determines glare control and shadow consistency across the playing surface. Buyers should request the lighting layout diagram, not just the wattage total, before finalizing electrical planning.
Table 1: Quick Specification Snapshot (H004)
| Component | Specification |
|---|---|
| Overall structure dimensions | 20,530mm × 7,700mm |
| Recommended minimum site size | 20,000mm × 6,000mm |
| Glass enclosure | 12mm tempered glass |
| Playing surface | 13mm pile, 8,000 Dtex, 52,500 density artificial turf |
| Steel mesh panels | 50×50mm grid, 3.0–4.0mm wire gauge |
| Lighting system | 8 × 200W LED fixtures (1,600W combined load) |
The H004's overall structural envelope is 20,530mm × 7,700mm, while the recommended minimum site footprint is 20,000mm × 6,000mm. This gap matters: the structure itself is larger than the "playing footprint" buyers often plan around, because the frame, mesh panels, and glass extend beyond the inner court lines.
Site planners should treat the recommended footprint as the floor, not the target. Adding clearance beyond the minimum supports:
A site that exactly matches 20,000mm × 6,000mm with no margin will likely feel tight in practice, particularly at the corners where players retrieve balls off the back glass.
The H004 can be installed in either setting, but each carries different planning requirements:
Indoor installations need to confirm:
Outdoor installations need to confirm:
Neither setting is inherently easier — each shifts the engineering burden to a different discipline (mechanical/structural for indoor, civil/drainage for outdoor).
Before installation begins, contractors should confirm the following is in place:
A well-structured RFQ for a padel court system should require suppliers to quote against a fixed specification, not a general description. Vague RFQs ("padel court with glass and lighting") invite mismatched bids that look comparable on price but differ significantly in component quality. At minimum, require quoted responses to state:
Table 3: Turnkey vs. Multi-Supplier Comparison
| Factor | Turnkey System | Multi-Supplier Sourcing |
|---|---|---|
| Installation risk | Lower — components pre-matched by one supplier | Higher — mismatched tolerances between vendors |
| Compatibility issues | Minimal — frame, glass, turf, and lighting engineered together | Common — separately sourced parts may not align dimensionally |
| Procurement time | Generally shorter — single point of contact and contract | Generally longer — multiple negotiations and delivery schedules |
| Engineering coordination load | Carried by the supplier | Carried by the buyer or their contractor |
This comparison isn't a universal argument for turnkey sourcing in every case — some buyers have existing relationships with steel fabricators or lighting contractors and prefer to manage coordination themselves. But for buyers without in-house engineering coordination capacity, a turnkey specification removes a significant project risk.
Padel court pricing varies based on a handful of factors that buyers should isolate when comparing quotes, rather than evaluating total price alone:
Before committing to a purchase, buyers can work through this sequence:
Each step gates the next. A site that fails space fit shouldn't proceed to commercial analysis until the footprint question is resolved — either by finding a larger site or confirming a smaller-format alternative exists.
What site size is required for the H004 single padel court?
The recommended minimum site footprint is 20,000mm × 6,000mm, while the structure's overall dimensions are 20,530mm × 7,700mm. Buyers should plan for clearance beyond the minimum footprint to allow for maintenance access and player run-off space.
Is the 12mm tempered glass suitable for active play?
Tempered glass is the standard material for padel enclosures because it resists impact and breaks into smaller, less hazardous fragments if it fails. At 12mm, the H004's glass sits at the thicker end of typical padel specifications, which supports durability under repeated ball and player contact.
What electrical capacity does the lighting system require?
The H004 uses 8 LED fixtures at 200W each, for a combined system load of 1,600W. Electrical contractors should size circuits and service capacity to this combined load before installation, in addition to confirming fixture placement for even court coverage.
What should a turnkey padel court RFQ include?
A complete RFQ should specify exact dimensions, glass thickness and panel layout, turf pile height/Dtex/density, lighting fixture count and layout, installation scope, and separate warranty terms for structural, glass, turf, and electrical components. Vague specifications make it difficult to compare bids on equal terms.
